Inserting Devices

    Solder Lug inserting Device Type A 040

    for solder lugs

    Component forms

    detailed description
    Specification
    - dimension 320 x 600 x 600 mm
    - weight approx. 20 kg
    - electrical 230V / 50 Hz / 100W
    - compressed air 3,5 to 4,0 bar
    - magazin 300 bis 400 solder lugs (threaded on wire)
    - production rate one per second
    remark: Insertion Device Type A 040/R for solder lugs out of a conveyor
    .
    Description:

     

    The solder lug insertion device Type A 040 is designed to insert pre-stored solder lugs into p. c. boards. The components are supplied automatically to the device, and will be pressed into the p. c. board by an air cylinder. Therefore, the p. c. board has to be held to the setting position manually, and a tracer finger then triggers the setting process.

    The inserting device will handle all usual in the trade solder lugs, which are lined up on wire or adhesive tape. Replacing the insertion head and the bin makes it possible, to process solder tags with different dimensions and forms. The re-tooling is easy, and takes only a few minutes.

    fewer…

    Solder lug inserting device with tape feeder Type A 040/B

    for solder lugs

    Component forms


    detailed description
    Specification
    - dimension 800 x 750 x 600 mm
    - weight approx. 20 kg
    - electrical 230V / 50 Hz / 100W
    - compressed air 3,5 to 4,0 bar
    - magazin roll
    - production rate one per second
    .
    Description:

    The solder lug inserting device Type A 040 B, was constructed for a mechanised insertion of solder lugs. Fixed cycles of less than one second are within easy reach. A Foot pedal controls the individual stroke sequence. The taped solder lugs are automatically fed into the machine. Therefore, no additional material and wage costs for threading the solder lugs on leads will arise.

    The device is able to process all kind of taped solder lugs with standard forms. After a slight alternation, solder lug strips, which deviate from standard, can also be processed. To do this, you simply have to replace the insertion head with stripe guide and the cutting tool, which is fast and easy to do. All driving elements and electrical switches belong to the main machine and therefore, they do not have to be moved.

    The bearing pedestal for the material bin can hold coils up to 500 mm ø. An adjustable conical ring centres the coil on the bearing pedestal.
    Working with this device is very easy and save.

    fewer …

    Solder lug inserting Device Type A 040 B-NC

    for solder lugs

    Component forms


    detailed description
    Specification
    - dimensions 1500 x 1200 x 1700 mm
    - size of the table 500 x 300 mm
    - process-way 380 x 250 mm
    - weight approx. 1.000 kg
    - electrical 230 V / 50 Hz / 1,1 kW
    - compressed air 6 bar
    - magazin loose components out of a circle conveyor, or taped components
    - production rate 3.500 pcs/hr
    .
    Description:

    The Burst & Zick device Type A 040 B-NC was constructed for the automatical insertion of solder lugs. The individual stroke sequence is program-controlled. The solder lugs are fed into the device on punch stripes, so no additional material and wage costs for threading the solder lugs on wire will arise.

    The device is able to process all kind of solder lugs on punch stripes with standard dimensions and forms. After a slight alternation, solder lug stripes, which deviate from standard, can also be processed. To do this, you simply have to replace the insertion head with stripe guide and the cutting tool, which is fast and easy to do. All driving parts and electrical switches belong to the main machine, and therefore, they do not have to be moved.

    By the use of taped solder lugs, the bearing pedestal can pick up coils with up to 500 mm Ø. An adjustable conical ring centers the coil on the bearing pedestal. With a conveyor for bulk material, loose solder lugs are moved into the device. The device can be setup with one or two setting tools.

    fewer …

    Solder lug inserting Device Type A 040 R

    for solder lugs from a bowl-feeder

    Component forms


    detailed description
    Specification
    - dimension 320 x 600 x 600 mm
    - weight approx. 20 kg
    - electrical 230V / 50 Hz / 100W
    - compressed air 3,5 to 4,0 bar
    - magazin 300 to 400 solder lugs
    - production rate one per second
    .
    Description:

    The Burst & Zick solder lug inserting device Type A 04 R is designed, to insert solder lugs into p. c. boards.

    The Solder lugs are automatically moved into the device by a vibrating conveyor. An air cylinder then presses them into the p. c. board. To do this, the p. c. board is to be held manually to the setting position. The setting process by itselve is triggered over an tracer finger.

    This inserting device is able to process all kind of usual in the trade solder lugs (incl. double tongues), which can be supplied by a conveyor for bulk materilas.

    fewer …

    Solder lug inserting Device Type A 041 with circuit bord guide and light point projector

    for solder lugs

    Component forms


    detailed description
    Specification
    - dimension 330 x 600 x 500 mm
    - weight approx. 15 kg
    - compressed air 6,0 bar
    - magazin 300 to 400 taped solder lugs
    - production rate one per second
    remark: for insertion of loose round pins over conveyor for bulk material, see Type A 042
    .
    Description:

    The device Type A 041 is designed, to insert stored solder lugs (solder posts) into
    p. c. boards, spool bodys or contact banks. The solder lugs are pressed into the p. c. boards by an Foot pedal-activated air cylinder. The p. c. board is centered by a insertion pin. The device can optionally be equipped with a light point adjustement. All usual in the trade solder lugs which are lined up on wire or adhesive tape can be processed.

    Retooling to different solder lug forms is possible and easy to do. The p. c. board is placed in the frame and will be adjusted. After that the p. c. board has to be shifted manually into the working area. The setting postion can be placed trough a luminous spot. The insertion itself is triggered by a Foot pedal.

    fewer …

    Round Pin inserting Device Type A 042

    for Round pins

    Component forms

     

    detailed description
    Specification
    - dimension 800 x 750 x 600 mm
    - weight approx. 25 kg
    - electrical 230V / 50 Hz / 100 W
    - compressed air 5,5 bar
    - magazin bulk material in the conveyor
    - production rate one per second
    .
    Description:

    The Burst & Zick inserting device Type A 042 offers the economical solution, for the mechanised insertion of round pins, solder posts and or -lugs into p. c. boards.

    With this device, nearly all customer forms of round pins, solder posts / -lugs can be processed. The loose components are filled into the sorting pot of the vibration conveyor. Trough barriers in the helical of the conveyor, the components are ordered. After positioning, the components are handed to the loading slider, which supplies the components to the inserting tool.

    Working with this device is save and easy: For assembling, hold the p. c. board with both hands on the edges, and place it under the inserting tool. The p. c. board now lies at the bottom of the pressure stamp, while the tooling pin hole is placed directly under the solder post / -lug shaft looming out of the inserting tool. This has the function of a locating pin. The p. c. board is lifted parallel, so the components shaft enters the tooling pin hole. The insertion process is triggered
    by a foot switch.

    fewer …

    Motor Press Type D 020

    pressing edge connectors into p.c. boards

    detailed description
    Specifications
    - Dimensions 440 mm x 700 mm x 380 mm
    - Weight ca. 20 kg
    - Electrical 230V / 50 Hz / 110W
    - Clamp Height min. 20 mm
    max. 90 mm
    - Working Area 340 mm x 230 mm
    - Operation triggered by end stop

    .
    Description:

    The Motorpress Type D 020 has been developed to press edge connectors, revitings and so on into p. c. boards. The press can also be used to join several p. c. boards or p. c. board components.

    Using different toolkits changed inside the master tool varying assembly sequences can be done much easier than doing the same before using a toggle lever press. Because of the dimensions, the Motorpress can be mounted on a working bench, or it can be made available on an assembly vehicle.

    The working method is easy: The p. c. board and the component are shifted into the working area. After meeting the end stop the switch starts the assembling process. Because of the nearly closed protection device there is no danger for the Operator.

    fewer …