Cut / Stamp / Bend

    Cutting and Bending Device Type C 034

    for loose or belted axial Components

    Component forms

    detailed description
    Specification
    - dimension 200 x 200 x 280 mm
    - weight approx. 6 kg
    - compressed air 4 to 6 bar
    - min. pitch C 034 S: 12,5 mm, C 034 MIL: 7,5 mm
    - max. pitch C 034 S: 100 mm, C 034 MIL: 100 mm
    - lead Ø C 034 S: 0,8 to 1,4 mm, C 034 MIL: 0,4 to 0,8 mm
    - components loose or belted (manual suplied)
    - operation manual via pneumatic Foot pedal
    - production rate 2.500 pcs/hr
    .
    Description:

    The Burst & Zick Device Type C 034 is designed to cut and bend the leads of axial components to a 90° configuration. Because of the independent adjustments for the lead span, the left cut length and right cut length, the device allows a wide variety of processing parameters.

    The components are hand fed into the tooling. The component body has to be centered between the bending anvils. After the Foot pedal is depressed, the component leads are clamped on both sides. The leads are then cut to length and bend to the required form. The processed component is then rejected by the front of the device.

    fewer …

    Cutting, Stamping and Forming Device Type C 042

    for loose or belted axial Components

    Bauteilformen

    detailed description
    Specification
    - dimension 300 x 500 x 210 mm
    - weight approx. 8 kg
    - compressed air 4 to 6 bar
    - min. pitch C 042: 10 mm, C 042/S: 12,5 mm
    - max. pitch C 042: 70 mm, C 042/S: 70 mm
    - lead Ø C 042: max.0,8 mm, C 042/S: max. 1,3 mm
    - components loose or belted
    - operation operation
    - production rate 2.500 pcs/hr
    .

    Description:

    The Burst & Zick Device Type C 042 is designed to cut, stamp and bend the leads of axial components.

    By the use of interchangeable tool sets a variety of form configurations can be achieved with this device. The change can be done easy and secured in less than two minutes.

    The settings will be displayed on the scale of the device. The embossing for the leads are tooling-specific. This tools are produced to meet customer requirements.

    The components are hand fed into the tooling. The component body has to be centered between the bending anvils. After the Foot pedal is depressed, the component leads are clamped on both sides. The leads are then cut to length and depending on the form shape the required lead features are put in the leads at this time. After that, the leads are bend to the 90° configuration. The processed component is then rejected by the front of the device.

    fewer …

    Cutting, Stamping and Forming Machines Type C 043

    for loose or belted axial Components

    component forms

       

    detailed description
    Specification
    - dimension 840 x 480 x 450 mm
    - weight approx. 45 kg
    - electrical 230 V / 50 Hz / 200 W 
    - bending tool horizontal and vertical bendings
    - min. pitch horizontal: 7,5 mm
    vertical: 2,5 mm
    - max. pitch horizontal: 50 mm
    vertical: 5 (7,5) mm
    - lead Ø horizontal: 0,4 to 1,3 mm
    vertical: up to 0,8 mm
    - components taped
    - production rate 8.000 pcs/hr (continuously variable)
    - Option  - manual supplyment for lose components
    - digital display for pitch and cutlength
    - survey for component-roll or ammo-pack 
    .

    Description:

    The Burst & Zick machine Type C 043 is designed, to cut stamp and bend axial leaded components for both horizontal and vertical mounting.

    To make the insertion of components with short leads into p. c. boards possible, the leads have to be cut to suitable length, bend to the required pitch and -if necessary- stamped.
    Both, suitable length and required pitch can be adjusted by adjusting screws. After this set-up the components can be processed. Option: the adjustments can be checked by a digital display.

    The stamping result for the leads depends on the used tool. These tools can be manufactured to meet customer requirements. The machine can be re-set for the different tools.

    The taped components can be processed automatically. The processing-speed is continuously variable. The tool change for different bending dimensions takes about 2 minutes.

    fewer …

    Cutting, Stamping and Forming Machines Type C 043 E

    for loose or belted axial Components

    component forms

        

    detailed description
    Specification
    - dimension 840 x 480 x 450 mm
    - weight approx. 45 kg
    - electrical 230 V / 50 Hz / 200 W 
    - bending tool horizontal and vertical bendings
    - min. pitch horizontal: 7,5 mm
    vertical: 2,5 mm
    - max. pitch horizontal: 50 mm
    vertical: 5 (7,5) mm
    - lead Ø horizontal: 0,4 bis 1,3 mm
    vertical: up to 0,8 mm
    - components taped
    - production rate 8.000 pcs/hr (continuously variable)
    - Option  - manual supplyment for lose components
    - pre-set and item counter
    - survey for component-roll or ammo-pack 
    .

    Description:

    The Burst & Zick machine Type C 043 E is designed, to cut stamp and bend axial leaded components for both horizontal and vertical mounting.

    To make the insertion of components with short leads into p. c. boards possible, the leads have to be cut to suitable length, bend to the required pitch and -if necessary- stamped.
    Both, suitable length and required pitch can be adjusted by adjusting screws. After this set-up the components can be processed. Option: the adjustments can be checked by a digital display.

    The stamping result for the leads depends on the used tool. These tools can be manufactured to meet customer requirements. The machine can be re-set for the different tools.

    The taped components can be processed automatically. The processing-speed is continuously variable. The tool change for different bending dimensions takes about 2 minutes.

    fewer …

    Cutting, Stamping and Forming Machine Type C 043 ES

    for loose or belted axial Components

    component forms

    detailed description
    Specification
    - dimension 600 x 480 x 450 mm
    - weight approx. 45 kg
    - electrical 230 V / 50 Hz / 200 W 
    - compressed air 6 bar 
    - bending tool horizontal bendings
    - min. pitch 7,5 mm
    - max. pitch 50 mm
    - lead Ø 0,4 to 1,3 mm
    - components taped
    - production rate 3.600 pcs/hr (continuously variable)
    - Option  - manual supplyment for lose components
    - digital display for pitch and cutlength
    - pre-set and item counter
    - survey for component-roll or ammo-pack
    .

    Description:

    To make the insertion of components with short leads into p. c. boards possible, the leads have to be cut to suitable length, bend to the required pitch and -if necessary- stamped.
    Both, suitable length and required pitch can be adjusted by adjusting screws. After this set-up the components can be processed. Cutting length and pitch are fully adjustable.

    The stamping result for the leads depends on the used tool. Leadforming ist tool specific and can be manufactured to meet customer requirements.

    The difference to the types C 043 and C 043 E is the integrated Pneumatic which makes the rearrangement of the Bending- and Formingtools possible. This means, that the tools can be approached to the components. Espacially bendings with Flush-Mount-bead can be done.

    The taped components can be processed automatically. The processing-speed is continuously variable. The tool change for different bending dimensions takes about 5 minutes.

    fewer …

    Cutting, Stamping and Forming Device Type C 044

    for axial leaded components for vertical mounting

    Component forms

       

    detailed description
    Specification
    - dimension 200 x 450 x 200 mm
    - weight approx. 8 kg
    - compressed air 5 to 6 bar
    - pitch min. 2,54 mm, max. 5,08 mm
    - component Ø min. 2 mm, max. 8 mm
    - component length min. 4 mm, max. 10 mm
    - lead Ø C 044: 0,4 mm to 0,8 mm, C 044 S: 0,9 mm to 1,4 mm
    - components loose or belted (manual supplied)
    - operation manual via pneumatic Foot pedal
    .

    Description:

    The Burst & Zick machine Type C 044 is designed, to cut and form the leads of axial components for vertical mounting.

    A variety of form shapes are avalaible through the use of interchangeable die sets. To make the insertion of components with short leads into p. c. boards possible, the leads have to be cut to suitable length and formed to required raster.

    The set up adjustments are quite simple and secured to provide accurate forming of every compöonent lead.

    fewer …

    Cutting- and Forming Device Type C 052 B

    for radial components

    Component forms

    Example of use

       

    detailed description
    Specification
    - Dimensions 350 x 100 x 200 mm
    - Weight ca. 15 kg
    - Compressed air 4 to 6 bar
    - Pitch min. 3,5 mm (2,5 mm on inquiry)
    max. 25 mm
    - wire Ø max. 0,8 mm
    - Operation pneumatic
    .

    Description:

    The Burst & Zick GmbH model C052/B is designed to cut and form radial components with 2 leads. A variety of form shapes are possible through the use of interchangeable die sets.

    Two Bending forms can be choosed:

    1. distance wave
    2. zz-Wave bended to inside or outside

    The die sets can be manufactured to customer specification.

    The triangular shaped center die allows components with lead spans from 3.5 mm to 20 mm to be processed on a single die. Adjustments are provided for the placement and exaggeration of the form.

    Easy to operate, the C052/B offers an economical solution to quality forming of loose, radial components.

    fewer …

    Cutting Device Type C 053

    for lose radial components

    Component forms

    detailed description
    Specification
    - dimension 300 x 130 x 120 mm
    - weight approx. 3 kg
    - compressed air 4 to 6 bar
    - pitch 2,5 mm and 2,54 mm
    - hole pattern 13 x 21 drill holes for edge connectors; circle pitches for operational amplifiers and transistors; and laterally slits for cutting components with long leads.
    - lead Ø 0,8 mm to 1,0 mm
    - cut length  standard 3 mm (different dimensions on inquiry)
    - operation pneumatic Foot pedal
    - production rate 2.000 pcs/hr
    - remark special drill hole pictures on inquiry
    .

    Description:

    The Burst & Zick Device Type C 053 is designed to cut the leads of axial or radial leaded components incl. IC's to required length.

    Cover plate and cutting tip are drilled with each other, so all leads will be cutted simultaneously. The plates are made of high-quality tool steel hardened to 60 HRC and polished.

    fewer …

    Cutting Device Type C 055 H

    for radial components

    Component forms

    detailed description
    Specification
    - dimension 280 x 140 x 120 mm
    - weight approx. 1,5 kg
    - pitch 13 x 21 drill holes
    - hole pattern TO 18/TO 92/TO 5: 2,54 x 1,27 mm; 5,08 x 2,54 mm;
    7,62 mm x 5,08 mm; Round-pitch for operational amplifiers with 8 and 10 leads; and laterally slit for cutting of components with long leads.
    - drill Ø 1,1 mm (others on inquiry)
    - cut length standard 3 mm (other dimensions on inquiry)
    - operation  manually
    - production rate  approx. 1.500 pcs/hr
    - remark   special drill holes on inquiry
    .

    Description:

    The Burst & Zick Devices Type C 055 H is designed to cut the leads of axial or radial leaded components incl. IC's to the required length.

    Cover plate and cutting tip are drilled with each other, so all leads will be cutted simultaneously. The plates are made of high-quality tool steel hardened to 60 HRC and polished.

    fewer …

    Cutting Device Type C 055 P

    for radial components

    Component forms

    detailed description
    Specification
    - dimension 280 x 140 x 120 mm
    - weight approx. 1,5 kg
    - compressed air 4 to 6 bar
    - pitch 13 x 21 drill holes
    - hole pattern TO 18/TO 92/TO 5: 2,54 x 1,27 mm; 5,08 x 2,54 mm;
    7,62 mm x 5,08 mm; Round-pitch for operational amplifiers with 8 and 10 leads; and laterally slit for cutting of components with long leads.
    - drill Ø 1,1 mm (others on inquiry)
    - cut length standard 3 mm (other dimensions on inquiry)
    - production rate  approx. 1.500 pcs/hr 
    - operation pneumatic foot pedal or manually via Hand
    - remark special drill holes on inquiry
    .

    Description:

    The Burst & Zick Device Type C 055 P is designed to cut the leads of axial or radial leaded components incl. IC's to the required length.

    Cover plate and cutting tip are drilled with each other, so all leads will be cutted simultaneously. The plates are made of high-quality tool steel hardened to 60 HRC and polished.

    fewer …

    Universal Cutting and Forming Device Type C 055 S

    for axial or radial components

    Component forms

      

    detailed description
    Specification
    - dimensions 280 x 140 x 120 mm
    - weight approx. 1,5 kg
    - compressed air 4 to 6 bar
    - pitch 2,5 mm to 30 mm
    - wire Ø 0,4 mm to 1,0 mm
    - cutting length tool specific
    - bending form/length tool specific
    - operation pneumatic foot pedal
    .

    Description:

    The Device Type C 055 S was developed espacially for the moderate cutting and forming of components with axial or radial leads (incl. ICs).

    Cutting and forming the leads will be done in one working cycle. Changing the die sets takes no longer than 5 minutes.

    fewer …

    Universal Cutting Device Type C 057

    for radial components, now with adjustable cutting length as an option

    Component forms

    detailed description
    Specification
    - dimension 420 x 200 x 70 mm
    - weight approx. 3,5 kg
    - compressed air 4 to 6 bar
    - pitch 2,5 mm and 2,54 mm
    - hole pattern 13 x 21 drill holes for edge connectors; Round-pitches for operational amplifiers and transistors; and laterally slit for cutting components with long leads.
    - lead Ø 0,8 mm to 1,3 mm (other Ø on inquiry)
    - cut length standard 3 mm (other dimensions on inquiry)
    - operation pneumatic Foot Pedal
    - production rate 2.000 pcs/hr
    - remark special drill hole pictures on inquiry
    - option  now available, adjusting device for cutting length from 3-25 mm
    .

    Description:

    The Burst & Zick device Type C 057 is designed to cut the leads of axial and radial components incl. ICs to the required length.
    Even female connectors can be processed with this device. A diagonal arranged cutting knife is be driven over the whole working surface, so each component terminal is cutted by itself.

    The plates are made of high quality tooling-steel, hardened to 60 HRC and polished.

    fewer …

    Universal Cutting Device Type C 058

    for radial components

    Component forms

    detailed description
    Specification
    - dimension 780 x 230 x 110 mm
    - weight approx. 28 kg
    - compressed air 6 bar
    - lead Ø Ø on inquiry
    - cut length standard 3 mm (other dimensions on inquiry)
    - operation pneumatic Foot Pedal
    - production rate 2.000 pcs/hr
    - option special drill hole pictures on inquiry
    .

    Description:

    The Burst & Zick device Type C 058 is designed to cut the leads of axial and radial components incl. ICs to the required length.
    Even female connectors can be processed with this device. A diagonal arranged cutting knife is be driven over the whole working surface, so each component terminal is cutted by itself.

    The plates are made of high quality tooling-steel, hardened to 60 HRC and polished.

    fewer …

    Universal Cutting Device Type C 060

    for jumper wires

    component form

    detailed description
    Specification
    - dimensions 900 mm x 250 mm x 300 mm
    - weight approx. 25 kg
    - wire Ø 0,5 mm; 0,6 mm; 0,7mm or 0,8mm
    - power supply 230 V, 50 Hz / 100 W
    - capacity 6.000 jumper wires/hrs.
    - pitch 5 mm to 75 mm
    - side leg mind. 3 mm
    .

    Description:

    The Burst & Zick GmbH model C060 is designed to cut and form 20 to 22 gauge jumper wires. The machine has an adjustable center to center distance and uses interchangeable die sets to vary the cut length.

    The wire straightener, feed clamp and backlash assembly combined with an adjustable feed stroke produce a precise jumper wire every time.

    fewer …

    Universal Cutting, Bending and Stamping Devices Devices Type C 062 and C 063

    for loose radial-leaded components

    Component forms

      only C 063

        

    detailed description
    Specification Typ C 0 62
    - dimension 160 x 150 x 110 mm
    - weigh approx. 3 kg
    - compressed air 4 to 6 bar
    - pitch arbitrary
    - lead Ø max. 1,3 mm
    - operation pneumatic Foot Pedal
    - delivered with one processing unit
    - production rate 1.000 to 1.500 pcs/hr
     
    Specification  Typ C 0 62 
    - dimension  230 x 107 x 110 mm 
    - weigh  approx. 4 kg 
    - compressed air  5 to 6 bar 
    - pitch  arbitrary
    - lead Ø  max. 1,3 mm 
    - operation  pneumatic Foot Pedal
    - delivered with  two processing units
    - production rate 1.000 to 1.500 pcs/hr
    .

    Description:

    The Burst & Zick devices Type C 062 and C 063 are designed to process loose components with radial leads. Cutting and bending of the leads is done in one step including integrated strength member to eliminate axial strength uppon the component case.

    If the process of a component includes cutting, bending and stamping, you need to have two processing units (Type C 063).

    fewer …

    Cutting Device Type C 066 H

    for taped radial components

    Component forms

    detailed description
    Specification
    - dimension 103 x 225 x 240 mm
    - weight approx. 2 kg
    - pitch arbitrary
    - tape holepitch 12,7 mm and 15 mm
    - lead Ø max. 1,0 mm
    - cut length 2,5 mm and more
    - operation manual
    - production rate 15.000 pcs/h
    .

    Description:

    With the Burst & Zick device Type C 066H, all taped radial components, which meet the IEC-specification, can be cutted to the desired length.

    fewer …

    Cutting Device Type C 066 HA

    for taped radial components with integrated touch-facility to eliminate belt tolerances

    Component forms

    detailed description
    Specification
    - dimension 530 x 310 x 310 mm
    - weight approx. 15 kg
    - pitch arbitrary
    - tape holepitch  12,7 mm or 15 mm
    - lead Ø max. 1,0 mm
    - cut length 2,5 mm and more
    - operation manual
    - production rate 5.000 pcs/h
    .

    Description:

    With the Burst & Zick device Type C 066 HA, all taped radial components, which meet the IEC-specification, can be cutted to the desired length.

    The integrated touch-facility for components eliminates any kind of belt tolerances.

    fewer …

    Cutting Device Type C 066 M

    for taped radial components

    Component forms

    detailed description
    Specification
    - dimension 530 x 310 x 310 mm
    - weight approx. 15 kg
    - power supply 230 V / 50 Hz / 100 W 
    - pitch arbitrary
    - tape holepitch 12,7 mm and 15 mm
    - lead Ø max. 0,8 mm
    - cut length 2,5 mm and more
    - operation by engine (continuously variable)
    - production rate 35.000 pcs/h
    .

    Description:

    With the Burst & Zick device Type C 066 HA, all taped radial components, which meet the IEC-specification, can be cutted to the desired length.

    The integrated touch-facility for components eliminates any kind of belt tolerances.

    fewer …

    Cutting Device Type C 066 MA

    for taped radial components with integrated touch-facility to eliminate belt tolerances

    Component forms

    detailed description
    Specification
    - dimension 530 x 310 x 310 mm
    - weight approx. 20 kg
    - electrical 230 V / 50 Hz / 100 W 
    - pitch arbitrary
    - tape holepitch 12,7 mm or 15 mm 
    - lead Ø max. 1,0 mm
    - cut length 2,5 mm and more
    - operation by engine (continuously variable)
    - production rate 5.000 pcs/h
    .

    Description:

    With the Burst & Zick device Type C 066 MA, all taped radial components, which meet the IEC-specification, can be cutted to the desired length.

    The integrated touch-facility for components eliminates any kind of belt tolerances.

    fewer …

    Cutting Device Type C 066 MA-Z

    for taped radial components with integrated touch-facility to eliminate belt tolerances

    Component forms

    detailed description
    Specification
    - dimension 530 x 310 x 310 mm
    - weight approx. 25 kg
    - electrical 230 V / 50 Hz / 100 W 
    - pitch arbitrary
    - pitch belthole 12,7 mm or 15 mm 
    - lead Ø max. 1,0 mm
    - cut length 2,5 mm and more
    - components  taped
    - operation by engine (continuously variable)
    - production rate 5.000 pcs/h
    - Optional  batch counter
    .

    Description:

    With the Burst & Zick device Type C 066 MAZ, all taped radial components, which meet the IEC-specification, can be cutted to the desired length.

    The integrated touch-facility for components eliminates any kind of belt-tolerances.

    fewer …

    Cutting, Stamping and Bending Machine Type C 067

    for power transistors TO 126, TO 127, TO 220 and similar components

    Component forms

          

    detailed description
    Specification
    - dimension 500 x 350 x 400 mm
    - weight approx. 20 kg
    - electrical 230 V / 50 Hz / 110 W 
    - pitch 2,5 mm and other
    - lead Ø any lead Ø of power transistors
    - operation by engine (continuously variable)
    - components loose or stick
    - production rate 3.500 pcs/hr
    - Optional  supply of components via round conveyor
    .

    Description:

    The Burst & Zick machine Type C 067 is designed to process power transistors of types TO 18, TO 92, TO 126, TO 127 and TO 220 with 3 or more radial leads. Also different components (e.g. LED's) can be processed, which fit into the supply-shaft of the machine.

    The operation of the machine is restricted on filling up the exchangeable feed magazine with components to be processed. Optionally the machine can be equipped with a round-conveyor, to supply loose components automatically to the machine for processing.

    The tools are equipped with strain relief-valves to eliminate stress to the component body, when the leads are bend and cut. Once formed and cut the component is stored in a collection bin, seperated from shavings.
    The tool-change for different forms takes less than 5 minutes.

    fewer …

    Cutting, Stamping and Bending Machine Type C 068

    for power transistors TO 126, TO 127, TO 220 and similar components

    Component forms

          

    detailed description
    Specification
    - dimension 1100 x 550 x 500 mm
    - weight approx. 20 kg
    - electrical 230 V / 50 Hz / 110 W 
    - pitch 2,5 mm and others
    - lead Ø any
    - operation by engine (continuously variable)
    - components loose or stick
    - production rate 3.500 pcs/hr
    .

    Description:

    The Burst & Zick machine Type C 068 is designed to process power transistors of types TO 18, TO 92, TO 126, TO 127 and TO 220 with 3 or more radial leads. Also different components (e.g. LED's) can be processed, which fit into the supply-shaft of the machine.

    The operation of the machine is restricted on filling up the exchangeable feed magazine with components to be processed. After the processing action the components are then desposited into a second tube for collection.

    The tools are equipped with strain relief-valves to eliminate stress to the component body, when the leads are bend and cut. Once formed and cut the component is stored in a collection bin, seperated from shavings.

    The tool-change for different forms takes only about 2 minutes.

    fewer …

    Cutting, Stamping and Bending Machine Type C 069

    for power transistors TO 126, TO 127, TO 218, TO 220 and similar components

    Component forms


      

          

    detailed description
    Specification
    - dimension 600 x 600 x 450 mm
    - weight approx. 40 kg
    - electrical 230 V / 50 Hz / 200 W 
    - compressed air 6 bar
    - model tool double-station (bending up and down at the same time)
    - pitch 2,5 mm and others
    - lead Ø any
    - operation engine (continuously variable)
    - components sticks or loose
    - production rate 3.500 pcs/hr
    .

    Description:

    Cutting and Forming Machine for horizontal & vertical Mounting and tube to tube feeding.

    The cutting and forming machine Type C 069 is designed to cut and form components with 3 up to 23 leads for vertical or horizontal mounting.

    The feed magazines and die sets are modular in design to allow quick set up changes. All cutting and forming parameters are manufactured to customer specification.

    fewer …

    Universal Cutting, Stamping and Bending Machine Type C 069 G

    for taped radial components with integrated touch-facility to eliminate belt tolerances

    Component forms

     

       

    detailed description
     
    Specification
    - dimension 1100 x 550 x 500 mm
    - weight approx. 30 kg
    - electrical 230 V / 50 Hz / 250 W 
    - compressed air 6 bar
    - tools double-processing unit (forming upwards and downwards is possible)
    - pitch 2,54; 5,08; 7,62 mm
    - lead Ø max. 0,8 mm
    - operation  engine (continuously variable)
    - components delivery: roll or ammo-pack
    outgoing: loose
    - Leistung  3.500 BE/h 
    - Optional - preselection counter and batch counter
    - tape-chopper
    - combined location for reel or ammo-pack
    .

    Description:

    To eliminate belt-tolerances the Burst & Zick machine Type C 069 G was developed with an integrated touch-facility. With this all usual in the trade component-belts which meet the IEC-Norm can effortless be processed. The component is formed and cut with a maximum tolerance of ± 0,1 mm. The supply of components is exclusively done by reel. For this the machine has a combined location for reel and amo-pack.

    To save set-up time all necessary toolkits for specific formings are mounted in one unit. These toolkits can be inserted or exchanged within a very short time. When inserting a toolkit the driving-mechanism automatically will be locked.

    The machine is prepared to keep 2 processing-units. One unit performs upward formings and the other performs downward formings. After the components have been formed and cut they are ejected into a bin for collection.

    fewer …

    Cutting, Stamping and Bending Centre Type C 069 S

    for power transistors TO 126, TO 127, TO 218, TO 220 and similar components

    Component forms


      

          

    detailed description
    Specification
    - dimension base machine: 600 x 600 x 450 mm
    hole plant: 1200 x 600 x 600 mm
    - weight approx. 60 kg
    - electrical 230 V / 50 Hz / 250 W 
    - compressed air 6 bar
    - model double-processing unit
    (forming upwards and downwards is possible)
    - pitch 2,5 mm and others
    - lead Ø any
    - operation by engine (continuously variable)
    - components delivery: sticks or loose
    outgoing: stick or loose in a bin
    - production rate  3.500 pcs/hr
    - No. Cassettes 2 pieces
    - No. of sticks per cassette - standard 8, optionally 12
    in charging hopper - standard 8, optionally 12
    .

    Description:

    The Burst & Zick Machine Type C 069 S is designed to process power transistors of the types TO 126 and TO 220 and others for vertical or horizontal mounting. Basicly components with up to 23 leads can be processed (more leads on inquiry).

    The machine C 069 S processes power transistors automatically from sticks. The standard cassette is equipped for 8 sticks. The processed components are sorted itno an empty stick in the filling device.

    The machine is prepared to keep 2 tool-blocks. One unit performs upward formings and the other performs downward formings. Each tool-block can keep two forming sets or cutting sets.

    fewer …

    Universal Cutting- and Forming Machine Type C 090

     

    >>Attention<<

    This machine is no longer available!
    By a given Machine Number spare parts still can be ordered.

    succeeding model: C 092

    .

    .

    .

    Cutting and Forming Machine Type C 091

     

    >>Attention<<

    This machine is no longer available!
    By a given Machine Number spare parts still can be ordered.

    succeeding model: C 093

    .

    .

    .

    Universal Cutting- and Forming Machine Type C 092

    for taped radial components

    Component forms

     

        

     

    detailed description
     
    Specification
    - dimensions 650 mm x 450 mm x 500 mm
    - weight approx. 35 kg
    - electrical  230 V / 50 Hz / 110 W 
    - control  Siemens SPS "LOGO" 
    - pneumatic 6 bar
    - pitch min: 2,5 mm, max.: form dependend
    - holepitch 12,7 mm and 15 mm
    - lead Ø 0,4 to 1,0 mm
    - components taped
    - delivery reel or ammopack
    - rate with touching max. 3.000 pcs/hr
    without touching max. 4.000 pcs/hr
    .

    Description:

    The Burst & Zick GmbH model C 092 has been developed to process taped components with holepitches of 12.7 mm and 15 mm with one machine. To eliminate any kind of inconsistencies due to variances in taping, this machine is fitted with a touch-tool that will verify the cut length.

    The machine was developed with two processing units for multiple die sets. The die inserts can be exchanged very quickly. Because of the dual processing-units a wide range of bending and stamping forms can be processed.

    Options:

    1. roll-off block for all in trade reels
    2. electronic counter, which cuts off the Automat automatically when the pre-defined number of items is reached.
    fewer …

    Universal Cutting- and Forming Machine Type C 093

     

    Component forms

      

    detailed description
     
    Specification
    - dimensions 650 mm x 450 mm x 500 mm
    - weight approx. 35 kg
    - electrical 230 V / 50 Hz / 110 W 
    - control Siemens-SPS "S7-200"
    - pneumatic 6 bar
    - pitch min. 2,5 mm; max. 7,62 mm
    - tape holepitch 12,7 mm and 15 mm
    - lead Ø 0,4 to 0,8 mm
    - components taped
    - delivery reel or ammopack
    - rate  3.600 pcs/hr
    .

    Description:

    The C O93 was designed to produce a "J" bend to one lead of a component that has polarity. CO93 incorporates a touch tool that ensures a specific lead length ± 0.1 mm even if the components are not taped to an exact tolerance.

    Optionally, the CO93 offers a C Tester that can test the components for correct polarity prior to the forming station and remove them if they fail.

    Because the CO93 only accepts components on tape, either reeled or ammo pack formats are acceptable. Also because of its flexibility, the CO93 allows the processing of components taped on 12.7 mm and 15 mm spacing by using easy-to-change tape guides and tools.

    Options:
    roll off block for all in trade reels, belt-chopper

    fewer …

    Universal Cutting Automat Type C 094

    for taped radial components

    Component forms

     

     similar forms on inquiry

    detailed description
     
    Specification
    - dimensions 500 x 400 x 500 mm
    - weight approx. 20 kg
    - electrical 230 V / 50 Hz / 110 W 
    - control Siemens SPS "LOGO" 
    - pneumatic 6 bar
    - pitch min: 2,5 mm, max.: form dependend
    - tape holepitch 12,7 mm and 15 mm
    - lead Ø 0,4 to 0,8 mm
    - components taped
    - delivery reel or ammopack
    - rate max. 4.000 pcs/hr
    .

    Description:

    The C094 was specifically designed for an efficient way of cutting radial taped components. Additionally, the system can be configured for 90? bending or forming of radial components. (For bending and forming specifications please contact us).

    Because the C094 only accepts components on tape, either reeled or ammo pack formats are acceptable. Also because of its flexibility, the C094 allows the processing of components taped on 12.7 mm and 15 mm spacing by using easy to change tape guides and tools.

    Options:
    electronic counter, which cuts off the Automat automatically when the pre-defined number of items is reached.

    fewer …

    Universal Cutting Automat Type C 095

    for taped radial components

    Component forms

     

    detailed description
     
    Spezification
    - dimensions 500 x 400 x 450 mm
    - weight approx. 20 kg
    - electrical 230 V / 50 Hz / 110 W 
    - control Siemens SPS "LOGO" 
    - pneumatic 6 bar
    - pitch min: 2,5 mm, max.: 10 mm
    - tape holepitch 12,7 mm and 15 mm
    - lead Ø 0,4 to 0,8 mm
    - components taped
    - delivery reel or ammopack
    - Leistung  5.000 BE/h
    .

    Description:

    The Automat C 095 was especially developed for the rational cutting of taped radial components.

    Supplyment of components is done exclusive over reels. Therefore the Automat has a combined survey. Because the C094 only accepts components on tape, either reeled or ammo pack formats are acceptable. Also because of its flexibility, the C095 allows the processing of components taped on 12.7 mm and 15 mm spacing by using easy to change tape guides and tools.

    Options:
    electronic counter, which cuts off the Automat automatically when the pre-defined number of items is reached.

    fewer …